Photon Sound Beam ……….___ Quick Start ___
Photon Sound Beam
___ Quick Start ___
Open case. Identify components;
1 Base unit
2 Glass tubes (Rare Gas Probes) (RGP)
1 or 2 RF Probes (Flat Pack)
Instructions
Before plugging unit into power source, first connect all the probes ~
Insert plugs from the RGPs securely into the jacks on the front of base unit.
Note, either RGP may be connected to either jack; no particular left/right orientation is required.
Plug multi-pin plug(s) from Flat Pack(s) into jacks on rear of base unit.
Plug the power cord into a voltage matched grounded electrical receptacle.
Check the front panel to see that no indicator lights are blinking.
If the pilot lamp on the right (Green lamp) “only” is blinking, depress the corresponding button once, after a few fading cycles, the lamp will go out.
If both the pilot lamp on the left (Red lamp) and the pilot lamp on the right are blinking, first turn off the lamp on the left (Power-Sending), next turn off the lamp on the right (Ground-Return).
You are now ready to “Wake-Up” the Photon Sound Beam properly.
Adjust intensity control (Dial in center) to counter-clockwise (Low) position.
Depress button on the right fully once to activate main power board.
The RF Probes are now on and can be applied. Also from this mode (The lamp on the right, Ground-Return side is blinking), the RGP (Photon Function) can be activated.
To power up the RGPs, depress the button on the left (Power-Sending) side.
The RGPs will now “Come Alive”. The RGPs will pulse with energy in one-second cycles (Energized for one half second then resting for one half second. The RGPs will also emit pulses of violet light.
The Photon Sound Beam is now fully operational and can be applied to the body.
Described below is a typical systemic maintenance application;
Sit or recline comfortably. Make sure the body will come in contact with no metal (Chair frame, table rim Etc.), (Jewelry is optional). Place the Flat Pack(s) on or near the body, particularly effective placement may be the middle of the chest, just below the throat (Location of Thymus gland), and/or any target area of concern. The Flat Packs do not need to touch the skin, but the energy to the body is stronger the closer they are.
Now you can place yourself in the “Photon Circuit”.
Grasp the glass tube of either RGP in one hand, and the glass tube of the other RGP in the other hand. In this application scenario hold the RGPs by the glass, not the handle. You will feel an electrical stimulation in the hand holding the RGP connected to the left (Power-sending) jack, and may feel a less intense stimulation in the hand holding the RGP connected to the right (Ground-Return) jack. The intensity with which you experience the “Photon Circuit” stimulation will vary, and is dependent on various factors of your dynamic living system and on what level the intensity control is set to.
If while you are holding the glass of a RGP your skin should come in contact with a mass of metal, or a hydrated system (Person, other animal, potted plant Etc.) a spark may arc between the two, and you may feel a mild shock. The spark can not harm you (The electricity is very low amperage) but will get your attention. Also, you can create the spark arc if you either make contact or brake contact between the skin and the RGP “Glass” during the half second “Energized” phase of the Photon Circuit on-off cycle. Again this can not harm you, but if the intensity control is adjusted to a high setting, and you wish to avoid the sensation, simply have all skin-to-glass connections made before activating the RGPs (Pushing the button on the left), or be sure to make or brake skin-to-glass contact during the half second off/rest phase of the Photon Circuit cycle (The half second when the probes are not lighted).
Maintaining the described application configuration for from 10 to 30 minutes will constitute a typical systemic Photon Sound Beam session.
To turn off the Photon Sound Beam please turn off the RGPs (Click the button on the left) first, then you may deactivate the main power board and the Flat Packs by clicking the button on the right.
Now the unit is off and you may wish to return the intensity control to the low (Counterclockwise) position so that it will be ready to start off gently the next time it is powered up.
Alternately, you may wish to precede the described complete systemic session with some time using only the Flat Pack(s) (RF Probe(s)), or to follow a session with some time using only the Flat Pack(s). A Flat Pack only session is considered a “Passive Session”.
Be sure to stay well hydrated, drink plenty of clean water before and after each session.
Questions? Call Billy @ 1 800 811 1482 or 928 776 0596
_________________________________________________
Links to More on the Photon Sound Beam
The History and Applications of the Photon Sound Beam
Understanding the Photon Sound Beam
Photon Sound Beam ___ Quick Start ___
Photon Sound Beam, points to ponder
___________________________________________________________________
Back to Dr Billy Health HOME PAGE
Back to Dr Billy Health HOME PAGE
*
Filed under: Photon Sound Beam on May 1st, 2007
Leave a Reply